|
See The Pressure Washer
In Action
|
|
HOME > Heavy duty power washers > Electric Design Specs > Electric Motor Diesel Burner Hot Water Power Washe > BE Pressure Sprayers > High Pressure Nozzles
|
Pipe, sewer and drain cleaning applications will usually require pressures between 1200 to 4000 PSI and more importantly utilize high flow rates to flush away debris. Sometimes a thrusting action is needed to pull the jetting hose long distances. Lines that are to be cleaned will determine spray pattern needed.
Ultimate Washer will provide any spray pattern listed below with the nozzle at no extra charge. All our high pressure nozzles are drilled depending on the pressure and flow from your pump. This will result in optimized equipment and cleaning performance. The choice of a particular nozzle will rely on jetting equipment and the applications, which include residential, commercial and municipal locations. We offer high pressure nozzles sizes from 1/8", suitable for small electric jetters used in residential applications. Typical production time for drilling of the pipe, drain or sewer nozzle you select is two days.
NOTE: Due to lack of support with warranty and returns, and in an effort to better serve our customers, we have decided to no longer use Aquamole as a supplier for this product and have identifed another good source for this product line.
Features:
- High pressure nozzles are drilled to match pump flow and pressure specs for optimum equipment performance.
- 2.0 GPM to 60 GPM flow range -- 1/8", 1/4", 3/8", 1/2", 3/4" & 1" NPT sizes.
- Heat treated 416ss for corrosion and wear resistance, rated to 10,000 PSI.
- Several spray patterns are available to satisfy all cleaning applications.
- Excellent for pipe cleaning, sewer and drain cleaning.
|
 |
Ordering Instructions: Choose the nozzle size, National Pipe Thread (NPT) size, spray pattern, flow rate and pressure you will be using. WE WILL DRILL UP TO 12 orifices at no charge. If you require more than 12 orifices, there will be a $1.50 per hole upcharge on each nozzle.
*** Only spray patterns listed below are available.
|
| Pipe, Sewer and Drain Cleaning Nozzles |
 |
Button Nose Jetting Nozzle
The Button Nose ("BN") nozzle is well suited for general drain cleaning applications. It's short body and smooth round nose make it ideal for tight turns in traps and elbows, reducing hang ups. We've increased the functionality over typical round nose sewer nozzles with the addition of a second grove which permits steeper thrust angles and more pulling power while maintaining a streamlined body. This unique design permits multiple angle combinations on one nozzle. Sewer nozzle kits available below.
Features:
- Rated up to 10,000 PSI and 60 GPM
- Heat Treated 416 Stainless Steel
- Ideal for Tight Turns in Traps and Elbows
- Short Body and Round Nose
- For Drain and Industrial Cleaning
* See drill patterns below to determine your nozzles type. WE WILL DRILL UP TO 12 orifices at no charge. If you require more than 12 orifices, there will be a $1.50 per hole upcharge on each nozzle.
(Shipping charge of $7.95 will apply on these items if the total order is less than $59.00)
| MODEL |
DESCRIPTION |
DIAMETER |
LENGTH |
PRICE |
| AP-AP0125RN-10 |
1/8" NPT Button Nose Nozzle |
.500" |
.687" |
$43.10 |
| AP-AP0250RN-10 |
1/4" NPT Button Nose Nozzle |
.625" |
.825" |
$44.50 |
| AP-AP0375RN-10 |
3/8" NPT Button Nose Nozzle |
.812" |
1.000" |
$47.50 |
| AP-AP0500RN-10 |
1/2" NPT Button Nose Nozzle |
1.000" |
1.187" |
$51.20 |
|
| |
| Button Drill Patterns |
| THRUSTER MOLE |
 |
Description: The Thruster has a 25 degree angle for maximum pulling power. Use in a plugged line situation or for runs greater than 150 ft.
Pattern: 1 forward jet (optional), 3 to 6 rear jets
Standard Pattern: 6 rear jets |
| PENETRATOR MOLE |
 |
Description: 35 degree Penetrating angle with super pulling power. Use in a plugged line situation or for runs between 100 to 150 ft.
Pattern: 1 forward jet (optional), 3 to 6 rear jets
Standard Pattern: 1 forward and 3 rear jets |
| FLUSHER MOLE |
 |
Description: The Flusher has a 45 degree angle with good pulling power. Use for runs up to 100 ft. A good general purpose cleaning nozzle.
Pattern: 1 forward jet (optional), 6 to 12 rear jets |
| SWEEPER MOLE |
 |
Description: 55 degree Sweeping angle, pulling similar power as Flusher mole, but offers wider angle for sweeping lines clean.
Pattern: 1 forward jet (optional), 6 to 12 rear jets |
| CORNER MOLE |
 |
Description: 55 degree Flushing angle combined with a 90 degree side jet to assist nozzle through corners, etc.
Pattern: 1 forward jet (optional), 1 side jet @ 90 degrees & 3 to 6 rear jets |
| MONSTER MOLE |
 |
Description: A dual angle nozzle combining the forces of both thrust and flush for superior pulling and cleaning power.
Pattern: 1 forward (optional), 2 to 3 rear jets @ 45 degrees & 2 to 3 rear jets @ 25 degrees |
|
 |
Jet Nose Jetting Nozzle
The Jet Nose ("J") nozzle is the standard in the industrial tube and pipe cleaning industry. However, the longer length and 45 degree nose also as a piercing rod in sewer & drain cleaning applications. One to four forward facing orifices will help to penetrate heavy grease, soap, or even ice filled lines. Great all-around high pressure nozzles! Sewer nozzle kits available below.
Features:
- Rated up to 10,000 PSI and 60 GPM
- Heat Treated 416 Stainless Steel
- Ideal for Piercing Heavily Blocked Lines
- Longer and Pointed Design
- For Industrial Tube Cleaning
* See drill patterns below to determine your sewer nozzle type. WE WILL DRILL UP TO 12 orifices at no charge. If you require more than 12 orifices, there will be a $1.50 per hole upcharge on each nozzle.
(Shipping charge of $7.95 will apply on these items if the total order is less than $59.00)
| MODEL |
DESCRIPTION |
DIAMETER |
LENGTH |
PRICE |
| AP-AP0125BS-10 |
1/8" NPT Jet Nose Nozzle |
.500" |
1.250" |
$46.20 |
| AP-AP0250BS-10 |
1/4" NPT Jet Nose Nozzle |
.625" |
1.250" |
$47.70 |
| AP-AP0375BS-10 |
3/8" NPT Jet Nose Nozzle |
.812" |
1.562" |
$50.70 |
| AP-AP0500BS-10 |
1/2" NPT Jet Nose Nozzle |
1.000" |
1.750" |
$53.60 |
|
| |
| Jet Drill Patterns |
| RAM |
 |
Description: Use a 35 degree penetrating angle for maximum pulling power or a 45 degree angle for greater flushing, use in a plugged line situation.
Pattern: 1 forward jet (optional), 3 to 6 rear jets |
| OFFSET |
 |
Description: Similar to the RAM pattern, but the 10 degree offset forward angle permits some sidewall cutting action.
Pattern: 1 forward (10 degree) & 3 to 6 rear jets |
| DEGREASER / DE-ICER |
 |
Description: A 45 degree angle is the default choice for this pattern. However, when faced with a longer run a 35 degree angle will provide extra pulling power.
Pattern: 3 forward jets @ 10 degrees, 6 to 12 rear jets @ 45 degreaser 35 degrees
Standard Pattern: 3 forward and 6 rear jets |
|
 |
Rotor Jet Nozzle
The Rotary Jet ("RJ") is a revolving nozzle utilizing the combined forces of 0 degree & 45 degree angles rotating under pressure, creating a continuous "wall of water" to maximize line restoration. A valuable feature of the RJ is the field replaceable rotor which extends the nozzle's service life. Each and every RJ sewer nozzle is tested before shipment to assure it's rotational capabilities. Please note that due to the close tolerances between the moving parts of a spinning nozzle, we recommend that before using the RJ high pressure nozzles in any drain line that a preliminary cleaning pass has been made with a BN or J Type nozzle first. Sewer nozzle kits available below.
Features:
- Rated up to 10,000 PSI and 60 GPM
- Heat Treated 416 Stainless Steel
- Ideal as a Finishing or Polishing Tool
- For Thorough Rinsing but Not Necessarily Heavy Blasting
- 360 Degree Coverage Inside a Pipe
* See drill patterns below to determine your nozzle type. WE WILL DRILL UP TO 12 orifices at no charge. If you require more than 12 orifices, there will be a $1.50 per hole upcharge on each nozzle.
(Shipping charge of $7.95 will apply on these items if the total order is less than $59.00)
| MODEL |
DESCRIPTION |
DIAMETER |
LENGTH |
PRICE |
| AP-AP0125SJ-10 |
1/8" NPT Rotor Jet Nozzle |
.540" |
1.27" |
$136.80 |
| AP-AP0250SJ-10 |
1/4" NPT Rotor Jet Nozzle |
.750" |
1.500" |
$183.45 |
| AP-AP0375SJ-10 |
3/8" NPT Rotor Jet Nozzle |
.875" |
2.312" |
$202.40 |
| AP-AP0500SJ-10 |
1/2" NPT Rotor Jet Nozzle |
1.000" |
2.875" |
$274.20 |
| AP-AP0750SJ-10 |
3/4" NPT Rotor Jet Nozzle |
1.375" |
3.70" |
$304.10 |
|
| |
| Rotor Jet Drill Patterns |
| STANDARD ROTOR JET PATTERN |
 |
Description: Maximum cleaning action from 90 degree side jets with 45 degree flushing / pulling angle. This pattern is standard for Sewer Squad Kits.
Pattern: 2 side jets @ 90 degrees & 2 rear jets @ 45 degrees |
| MAXIMUM FLUSHING / PULLING PATTERN |
 |
Description: The 45degree flushing angle provides the maximum amount of flushing action. This pattern is also used on smaller pumps with lower flows to maximize pulling power for long runs.
Pattern: 2 rear jets @ 45 degrees |
|
| High Pressure Nozzle Kits |
 Select a high pressure nozzle kit to suit your specific needs. Available in 3, 4, 5 and 6 nozzle sets, the kits are drilled per order for a range of high pressure cleaning applications. Orders can ship in 48 hours. Choose your desired flow and pressure at checkout to match the nozzle selection with your equipment. High grade stainless steel construction provide for ultimate corrosion resistance and longevity. Kit nozzles can be bought by the piece if one is misplaced. Buying them as a kit saves money over purchasing individually and provides the user an all inclusive cleaning solution. Depending on the diameter of the sewer jetter hoses used, nozzle diameter chosen will allow for cleaning lines from 1” to 24”.
|
3-PC Nozzle Kit
4-PC Nozzle Kit
5-PC Nozzle Kit
6-PC Nozzle Kit
|
Sewer Nozzle Solution Kits
High pressure nozzle kits are available from .125" up to 1.00" and will clean lines from 1" to 24”. Custom drilled and can ship within 48 hours.
- Kits come with selected nozzles, cleaning tool, and storage container.
- Various Sizes Available: 1/8”, 1/4”, 3/8”, and 1/2” FNPT
- Maximum Pressures range Between 1,200 – 15,000 PSI
- Flow Rates Between 1.7 – 80 GPM
- 416 L Grade Stainless Steel
- Made in the U.S.A.
Ordering Information - FREE Shipping
See kit options below for descriptions of nozzle kit variations.
| MODEL |
DESCRIPTION |
NO. OF NOZZLES |
PRICE |
| AP-AP0125SS-03 |
1/8" Sewer Nozzle Kit |
3 PC |
$174.00 |
| AP-AP0125SS-04 |
1/8" Sewer Nozzle Kit |
4 PC |
$193.00 |
| AP-AP0125SS-05 |
1/8" Sewer Nozzle Kit |
5 PC |
$228.00 |
| AP-AP0125SS-06 |
1/8" Sewer Nozzle Kit |
6 PC |
$254.00 |
| AP-AP0250SS-03 |
1/4" Sewer Nozzle Kit |
3 PC |
$199.00 |
| AP-AP0250SS-04 |
1/4" Sewer Nozzle Kit |
4 PC |
$234.00 |
| AP-AP0250SS-05 |
1/4" Sewer Nozzle Kit |
5 PC |
$240.00 |
| AP-AP0250SS-06 |
1/4" Sewer Nozzle Kit |
6 PC |
$249.00 |
| AP-AP0375SS-03 |
3/8" Sewer Nozzle Kit |
3 PC |
$234.00 |
| AP-AP0375SS-04 |
3/8" Sewer Nozzle Kit |
4 PC |
$240.00 |
| AP-AP0375SS-05 |
3/8" Sewer Nozzle Kit |
5 PC |
$278.00 |
| AP-AP0375SS-06 |
3/8" Sewer Nozzle Kit |
6 PC |
$304.00 |
| AP-AP0500SS-03 |
1/2" Sewer Nozzle Kit |
3 PC |
$275.00 |
| AP-AP0500SS-04 |
1/2" Sewer Nozzle Kit |
4 PC |
$291.00 |
| AP-AP0500SS-05 |
1/2" Sewer Nozzle Kit |
5 PC |
$328.00 |
| AP-AP0500SS-06 |
1/2" Sewer Nozzle Kit |
6 PC |
$355.00 |
|
| |
Kit Options
- 3 Piece Kit: one Penetrator, one Flusher, and one Polisher
- 4 Piece Kit: one Penetrator, one Flusher, one Polisher, and one De-Icer/De-Greaser
- 5 Piece Kit: one Penetrator, one Flusher, one Polisher, one De-Icer/De-Greaser, and one Impactor
- 6 Piece Kit: one Penetrator, one Flusher, one Cornering, one Polisher, one De-Icer/De-Greaser, and one Impactor
| Sewer Kit Nozzles |
 |
Penetrator
Dislodges blockage
Pattern: 1 Forward Jet, 3 Back Jets |
Flusher
Flushes loose debris
Pattern: 6 Back Jets |
Cornering
Navigates around P-Traps and tight bends
Pattern: 1 Forward Jet, 1 Side Jet, 3 Back Jets |
Polisher
Polishes and maximizes line recovery
Pattern: 2 Side Jets, 2 Back Jets |
De-Icer/De-Greaser
Removal of heavily blocked lines with grease, hard soap or even ice
Pattern: 3 Forward Angle Jets, 6 Back Jets |
Impactor
Moves sand, grit and light scale which may have accumulated within the line
Pattern: 1 Forward Jet, 3 Side Jets, 6 Back Jets |
|
Can we improve something on this page?
Can this page be improved? Is the information complete and easy to understand? We are always looking to improve our website, so please feel free to give us your comments, suggestions, or questions. Thanks for helping us serve you better!
|
|
|
|
|
)
)
)
)
)
)
)
